立即博

秸秆颗粒机厂家如何更换立式环模颗粒机的研磨工具

来源:http://www.comicbopk.com 发布时间:2019-06-27 浏览次数:
  如何更换立式环模颗粒机的磨削工具?购买颗粒机用户现场安装人员在我们公司将培训如何取代木材颗粒机研磨工具,因为用户设备安装到位后,忙碌的试生产产品的,所以一些制造商从事设备安装和调试,以及用户的注意力集中在设备的性能,常常忽视了后期需要工人操作磨具来取代自己的问题。为了帮助更多的用户掌握球团机磨床刀具的更换,济南龙腾新能源写了这篇文章希望能对您有所帮助。(操作方法仅适用于立式环模造粒机)
  How to replace the grinding tools of vertical ring mould granulator? Buy the installers of granulator users in our company will train how to replace the wood granulator grinding tools. Because the user equipment is installed in place, busy trial production products, so some manufacturers are engaged in equipment installation and debugging, and the user's attention is focused on the performance of the equipment, often ignoring the need for workers to operate later. Make abrasives to replace your problems. In order to help more users to master the replacement of pelletizer grinder tools, Jinan Longteng New Energy wrote this article hoping to help you. (The method of operation is only applicable to vertical ring granulator)
  秸秆颗粒机厂家如何更换立式环模颗粒机的研磨工具
  How to Replace the Grinding Tool of Vertical Ring Mould Granulator by Straw Granulator Manufacturers
  首先松开制粒机上料板的螺丝,用设备配置的升降机或手动葫芦将上料板整体提起。下料盘前,请确认压杆自动润滑系统的注射管已断开。
  First, loosen the screw of the feeding plate of the granulator, and lift the feeding plate as a whole with the elevator or manual hoist equipped with the equipment. Before discharging, please make sure that the injection tube of the automatic lubrication system of the pressure rod has been disconnected.
  然后拆卸并安装压片机周围的压片螺钉,并拆卸压片机。由于磨具的固定压块为圆锥形,螺杆松动后不易得到。因此,颗粒机在每个压块的底部预留一个顶孔,并用千斤顶顶起压块。
  Then remove and install the press screw around the press, and remove the press. Because the fixed block of the abrasive tool is conical, the screw is not easy to get after loosening. Therefore, the granulator reserves a jacking hole at the bottom of each block and lifts the block with a jack.
秸秆颗粒机厂家
  秸秆颗粒机厂家如何更换立式环模颗粒机的研磨工具
  How to Replace the Grinding Tool of Vertical Ring Mould Granulator by Straw Granulator Manufacturers
  三、取下压块后,通过造粒机磨具顶部预留的两个模具提升孔,安装上提升螺丝。收紧新闻栏取消之前,磨料起重差距留出了空间,因为木屑颗粒机研磨工具是固定的很长一段时间,它可能不是容易起飞时删除它,所以有必要用锤子敲打振动,然后把磨具。
  3. After removing the block, the lifting screw is installed through two die lifting holes reserved at the top of the abrasive tool of the granulator. Before tightening the news column, there was room for the abrasive lifting gap, because the grinding tool of the sawdust granulator was fixed for a long time, and it might not be easy to delete it when taking off, so it was necessary to beat the vibration with a hammer and then put the abrasive.
  四、拆下模具后,清洗磨具安装槽,然后提起并放置新的磨具。确认到位后,依次安装磨具压块,拧紧。
  4. After removing the mould, clean the installation groove of the abrasive tool, then lift and place the new abrasive tool. After confirmation, install abrasive block in turn and tighten it.
  安装完成后,调整磨具与压棒之间的间隙,确保锯末造粒机的正常生产。螺杆安装好后,抬起并安装进给盖,连接自动加油管。
  After installation, the clearance between the abrasive tool and the pressure bar is adjusted to ensure the normal production of the sawdust granulator. After the screw is installed, the feed cover is lifted and installed, and the automatic filling pipe is connected.
  更换磨具后,我们将开始研磨新的磨具。由于新型磨具在加工和生产过程中有很多毛刺,所以每次更换新的磨具时都需要进行研磨。研磨完成后,即可正常生产。如果您遇到操作上的困难,可以向龙腾工程师咨询详细的解决方案。我们的网站是http://www.comicbopk.com
  After changing the abrasives, we will start grinding new ones. Because the new Abrasives have many burrs in the process of processing and production, it is necessary to grind each time new abrasives are replaced. After grinding, normal production can be achieved. If you encounter operational difficulties, you can consult Longteng Engineer for detailed solutions. Our website is http://www.comicbopk.com.

上一篇:立即博生物质颗粒机生产厂家:颗粒机减速机伞齿为什么用不了几天

下一篇:生物质颗粒机生产厂家质量鉴别规范这些必需看

广东11选5开奖结果 广东11选5开奖结果 大圣棋牌APP下载 立即博 大圣棋牌 广东11选5 大圣棋牌官网版下载 广东11选5走势图 大圣棋牌APP下载 大圣棋牌