即时比分网

顆粒機生產過程中應該加強什么管理?

來源:http://comicbopk.com 發布時間:2019-12-21 瀏覽次數:
  只有正常生產才能達到預期的效果。制粒機的生產是一樣的,每一個環節都要小心,口罩要仔細。那么在制粒機的生產過程中應該加強哪些管理呢?
  Only normal production can achieve the expected effect. The production of pelletizer is the same, every link should be careful, masks should be careful. So what management should be strengthened in the production process of granulator?
  1、對于顆粒機的進口進行管理,不同的生物質物料應存放在單獨的倉庫和特殊場所,遠離(易燃、易爆、火源),并注明原料名稱、濕度和采購日期。球團機生產線倉管員統一編號球團機進料口,繪制完整的現場區域分布圖,分別通知實驗室、控制操作工、設備經理、給料員,并配合上述人員確定各物料的給料口號和入庫。
  1. For the import management of the granulator, different biomass materials should be stored in separate warehouses and special places, away from (flammable, explosive, fire source), and marked with the name of raw materials, humidity and purchase date. The warehouse keeper of the pelletizer production line shall number the pelletizer feed port uniformly, draw a complete site area distribution map, respectively inform the laboratory, control operator, equipment manager and feeder, and cooperate with the above personnel to determine the feed slogan and warehousing of each material.
  2. 加強對物料、粉塵等的管理。每個入口都應標明造粒機儲存的原料的名稱和濕度;每臺給料造粒機都應標示與冷卻器和振動篩相同的規格和編號。;每條球團生產線由專人管理。生物質物料入庫時,物料接收人員和供應商人員應進行核對并簽字確認,以防止在投料過程中出現失誤,造成生產損失。球團機生產線倉管員統一編號原料入口,制作入口分布圖,分別通知實驗室和控制設備經理。
  2. Strengthen the management of materials, dust, etc. Each inlet shall be marked with the name and humidity of the raw materials stored in the granulator; each feed granulator shall be marked with the same specification and number as the cooler and vibrating screen. Each pelletizing production line is managed by a specially assigned person. When the biomass materials are put into storage, the material receiving personnel and the Supplier personnel shall check and sign for confirmation, so as to prevent mistakes in the feeding process and production losses. The warehouse keeper of pelletizer production line shall number the raw material entrance uniformly, make the entrance distribution diagram, and inform the laboratory and control equipment manager respectively.
木屑顆粒機批發
  我們經常在它發生之前談論預防,那么如何可能早期預防粒子失效呢?
  We often talk about prevention before it happens, so how can we prevent particle failure early?
  該設備應存放在干燥的室內,不得在酸性等腐蝕性氣體在大氣中循環的地方使用。
  The equipment shall be stored in a dry room and shall not be used in places where corrosive gases such as acid are circulated in the atmosphere.
  2. 定期檢查零件,每月檢查一次。檢查包括蝸輪、蝸輪、潤滑塊上的螺栓、軸承等運動部件是否正常。轉動和磨損靈活。如果發現任何缺陷,應及時修復,不再使用。
  2. Check the parts regularly and once a month. Check whether the moving parts such as worm gear, worm gear, bolts and bearings on the lubrication block are normal. Flexible rotation and wear. If any defect is found, it shall be repaired in time and no longer used.
  3.當造粒機使用或停止使用時,應取出轉鼓,將桶內剩余的粉劑(僅用于造粒機單元的一部分)進行清洗和刷掉,然后正確安裝,以便下次使用。
  3. When the granulator is in use or out of use, take out the drum, clean and brush off the remaining powder in the drum (only used for a part of the granulator unit), and then install it correctly for the next use.
  4. 在使用過程中,當滾筒前后移動時,前軸承掣子上的M10螺絲應調整到適當的位置。如果齒輪軸在移動,請將軸承架后面的M10螺絲調整到適當的位置,調整間隙,使軸承不發出噪音,用手轉動皮帶輪,適當擰緊。如果太緊或太松,機器可能會損壞。
  4. During the use, when the drum moves back and forth, the M10 screw on the front bearing dog shall be adjusted to a proper position. If the gear shaft is moving, please adjust the M10 screw behind the bearing frame to a proper position, adjust the clearance so that the bearing does not make noise, turn the pulley by hand and tighten it properly. If it is too tight or too loose, the machine may be damaged.
  5. 如果機器停機時間長,必須將整個機體的顆粒單元擦拭干凈,機器零件的光滑表面必須涂上防銹油,并用抹布覆蓋。
  5. If the machine is shut down for a long time, the particle unit of the whole body must be wiped clean, and the smooth surface of the machine parts must be coated with antirust oil and covered with a rag.

上一篇:生物質顆粒機孔的橫截面大部分為圓形

下一篇:最后一頁

重庆彩票 重庆彩票 重庆彩票 上海时时乐 上海时时乐 专业玩彩 专业玩彩 专业玩彩