即时比分网

木屑顆粒機流量顯著降低時手動排出冷卻器

來源:http://comicbopk.com 發布時間:2019-11-28 瀏覽次數:
  木屑顆粒機關機順序與啟動相反,相關設備根據工藝流程從前到后依次關閉。 當谷物儲存箱的低位定位器沒有顯示任何物料時,打開木屑顆粒機的人工進料門并觀察入口的流動狀態。
  The shutdown sequence of sawdust granulator is opposite to that of start-up, and relevant equipment is shut down from front to back according to the process flow When the low level positioner of the grain storage tank does not display any material, open the manual feeding door of the chip granulator and observe the flow status of the inlet.
木屑顆粒機
  小編指出,當流量顯著降低時,手動排出冷卻器,增加機器的流量,增加造粒機進料口的流量,保證造粒質量。 此時,需要注意回油管是否堵塞。 如果回流管堵塞,則手動卸下冷卻器并將機器轉回。 如果回流管未堵塞,請等待進料口觀察。在返回管道中完成材料后,等待幾分鐘,然后將材料釋放到冷卻器中,這樣回流管中只有少量的回收材料,這可以減少對下一次生產的污染。
  According to Xiaobian, when the flow rate is significantly reduced, manually discharge the cooler, increase the flow rate of the machine, increase the flow rate of the feed port of the granulator, and ensure the quality of granulation At this time, pay attention to whether the return pipe is blocked If the return line is blocked, manually remove the cooler and turn the machine back If the return line is not blocked, wait for the feed port to observe. After the material is finished in the return pipe, wait for a few minutes, and then release the material to the cooler, so that there is only a small amount of recycled material in the return pipe, which can reduce the pollution to the next production.
  剛購買的新木屑顆粒機模板需要磨合,因此新機器需要使用添加的脂肪飼料(5公斤飼料,1.5公斤細砂,2公斤) 發動機油,無需加水),一般來說,飼料的水分應控制在4-6%之間。 調整壓力輥和模板之間的間隙使其約1毫米。 調整壓力輥后,固定螺栓進行擰緊。 (如果模板被阻擋,則需要用手鉆檢查刀口和過濾網并重新填充。刀口和過濾器之間的間隙應適合鋸末機電機反轉。電機反轉可以小心!有時輸出結束,有時不輸出,這通常與電機的正負旋轉無關。當它的好壞時,它與木屑顆粒機模板的老化程度有關。
  The newly purchased new sawdust granulator template needs to be run in, so the new machine needs to use the added fat feed (5kg feed, 1.5kg fine sand, 2kg) engine oil, without adding water). Generally speaking, the water content of feed should be controlled between 4-6% Adjust the gap between the pressure roller and the template to about 1mm After adjusting the pressure roller, tighten the fixing bolts (if the formwork is blocked, the knife edge and filter screen need to be checked with a hand drill and refilled. The gap between the knife edge and the filter shall be suitable for the reverse rotation of the saw motor. Be careful when reversing the motor! Sometimes the output ends, sometimes it does not output, which is usually independent of the positive and negative rotation of the motor. When it is good or bad, it is related to the aging degree of the sawdust particle machine template.
  對于木屑顆粒機,加油是一種不可避免的使用操作。 這對于木屑顆粒機的維護和維護至關重要。 但是,有一種方法可以跟進加油。 如果你想不到它,你可以進行加油操作。木屑顆粒機加油應按五項進行。 定期:根據潤滑卡規定的周期加油,加油和清油。 對于大型石油儲備,應按規定的時間對其進行取樣和測試,并根據油質條件對油進行清洗和上油。
  For the chip granulator, refueling is an inevitable operation This is very important for the maintenance of the chip granulator However, there is a way to follow up If you can't think of it, you can refuel. Fueling of sawdust granulator shall be carried out according to five items Regular: refuel, refuel and clear oil according to the cycle specified by the lubrication card For large oil reserves, they should be sampled and tested according to the specified time, and cleaned and oiled according to the oil quality conditions.

上一篇:生物質顆粒機生產的顆粒燃料屬于生物質可再生能源

下一篇:最后一頁

重庆彩票 重庆彩票 重庆彩票 上海时时乐 上海时时乐 专业玩彩 专业玩彩 专业玩彩