即时比分网

生物質顆粒機生產廠家分享環模配件使用完畢如何處理

來源:http://comicbopk.com 發布時間:2019-11-12 瀏覽次數:
  顆粒機關閉時,應使用無腐蝕性的將原來的油環的模具部分飼料擠壓,否則,環模部分的熱量將留在模具孔飼料的原料干燥困難,導致如下:(2)開始生產,環模配件承擔高壓力,削弱它的力量,這可能會導致環模配件開裂;(3)部分模具孔堵塞,產量和效益下降。2、環模配件使用一段時間后,應檢查環模配件表是否有局部凸出的部分,如有此現象,應將環模配件進行修理,以確保……
  When the particle mechanism is closed, the feed of the original oil ring die should be extruded by non corrosive way, otherwise, the heat of the ring die part will remain in the feed of the die hole, which is difficult to dry, resulting in the following: (2) starting production, the ring die parts bear high pressure and weaken its force, which may lead to cracking of the ring die parts; (3) part of the die hole is blocked, and the output and benefit decrease. 2. After using the ring mold accessories for a period of time, check whether there is any part protruding in the ring mold accessories list. If there is such a phenomenon, repair the ring mold accessories to ensure that
  當顆粒機停機時,在環模配件內的進料應擠出無腐蝕性的油,否則,在環模配件內的熱量會使原料在飼料的模孔內干燥變硬,造成以下情況:
生物質顆粒機生產廠家
  When the granulator is shut down, the feed in the ring die fitting shall be extruded with non corrosive oil, otherwise, the heat in the ring die fitting will make the raw material dry and hard in the die hole of the feed, resulting in the following conditions:
  ()操作開始時,模具孔堵塞,物料無法擠出;
  () at the beginning of operation, the die hole is blocked and the material cannot be extruded;
  (2)生產初期,環模配件受力大,強度變弱,容易造成環模配件開裂;
  (2) at the initial stage of production, the ring mold parts are subject to large stress and weak strength, which is easy to cause cracking of the ring mold parts;
  (3)部分模具孔堵塞,產量和效益下降。
  (3) some die holes are blocked, the output and benefit decrease.
  合金鋼環模
  Alloy steel ring die
  2、環模配件在一段時間后,應檢查環模配件表是否有局部凸的部分,如果有這樣一個現象,環模配件應該維護,以確保環的輸出模具配件和輥的使用壽命。
  2. After a period of time, the ring die parts list shall be checked to see if there is any local convex part. If there is such a phenomenon, the ring die parts shall be maintained to ensure the service life of the ring output die parts and rollers.
  3、環模配件儲存在干燥、清潔的地方,如果儲存在潮濕的地方,會產生模孔腐蝕,降低環模配件或無材料的使用壽命。
  3. The ring mold accessories shall be stored in a dry and clean place. If they are stored in a wet place, the mold hole corrosion will occur, reducing the service life of the ring mold accessories or materials.
  4. 當裝卸環模零件時,不要用錘子等硬鋼質工具敲打環模零件表面。
  4. When loading and unloading the ring die parts, do not knock the surface of the ring die parts with a hammer or other hard steel tools.
  5、應做好各班環模配件的使用記錄,以統計環模配件的實際使用壽命。
  5. The use records of the ring mold accessories of each shift shall be made to count the actual service life of the ring mold accessories.
  6、若孔塞未出料,可采用油浸或食用油經新造粒后,仍不能使造粒可用電鉆將孔塞材料鉆出,再用含油性材料加細砂打磨拋光使用。
  6. If the plug is not discharged, oil immersion or edible oil can be used for granulation, but the plug material can not be drilled out by electric drill, and then the oil-bearing material can be used for grinding and polishing with fine sand.
  以上是生物質顆粒機生產廠家分享的環模配件在使用結束時的處理方法,希望對您有所幫助。想要了解更多內容,歡迎訪問網站:http://comicbopk.com
  The above is the treatment method of the ring mold parts shared by the biomass granulator manufacturer at the end of use, hoping to help you. For more information, please visit http://comicbopk.com

上一篇:木屑顆粒機批發要選大的是為了什么?

下一篇:經過秸稈顆粒機廠家加工過的棉桿有什么用處 ?

重庆彩票 重庆彩票 重庆彩票 上海时时乐 上海时时乐 专业玩彩 专业玩彩 专业玩彩